Licensed in the 5 New York City Boroughs (Queens, Brooklyn, Manhattan, The Bronx and Staten Island), Nassau County, Westchester, Rockland County and Yonkers.


    SPAD-logo (2).jpg

    Go Solar/Green NY LLC is a BBB Accredited Business. Click for the BBB Business Review of this Solar Energy System Design & Installation in Hollis NY



    Quick Contact

    1. Name
      Invalid Input
    2. Phone Number
      Invalid Input
    3. Email Address:
      Invalid Input
    4. Address:
      Invalid Input

    Standalone Solar Power Systems: Off grid solar and remote power generation

    Standalone Solar Power Systems are completely independent from any electric utility grid. They are most often used in remote areas where electricity is not available or where the connection fees of the grid are higher than the cost of an alternative energy system. Standalone solar systems (also known as autonomous, or off grid systems) are used to collect and store solar energy to be used by household appliances. These systems typically generate from 100 Watts (very small systems) to 5 kilowatts (larger systems, multi family homes). During the day, the electricity generated is used to power the home and charge the batteries. At night, and during rainy days, all necessary power is provided by the batteries.
    Stand alone solar
    In some cases, where it is important that power is always available, some stand alone
    systems, known as PV-hybrid systems or island systems, may also have another source of power such as a wind turbine, bio-fuel or a diesel generator. 
    Power generated from a stand alone system is considered DC (direct current), and is stored in a battery and converted to AC (alternate current). Standalone Solar Power Systems are the perfect choice for remote rural or villages to provide continuous reliable power. 
    Go Solar provides Standalone Solar Power Systems for:
        •       Villages in remote areas
        •       Private homes and offices
        •       Microwave/Radio repeater stations
        •       Medical facilities in rural areas 
        •       Emergency communications
        •       Water quality and environmental data monitoring
        •       Drinking water and livestock water pumping
        •       Irrigation pumping
        •       Aviation obstruction lights
        •       Environmental data monitoring
        •       Railway signals
        •       Street lighting
        •       Desalination


    What are the components of a standalone solar system?


    Solar modules are only one part of a standalone solar system. They work together with other components: batteries, inverters, and transformers. Together with power distribution panels and metering devices they complete the process.
    Solar Panels
    The DC electricity produced by the solar panel or module(s) is used to charge batteries via a solar charge controller. Any DC appliances that are connected to the battery will need to be fused. DC lights are normally connected to the charge controller. Any AC appliances are powered via an inverter connected directly to the batteries. Most standalone solar systems need to be managed properly. Users need to know the limitations of a system and tailor energy consumption according to how sunny it is and the state of charge (SOC) of the battery.
    The solar panels need to be configured to match the system DC voltage, which is determined by the battery. System voltages are typically, 12V DC and 24V DC, larger systems will operate at 48V DC.
    The operating voltage of a solar panel in a stand-alone system must be high enough to charge the batteries. For example, a 12V battery will require 14.4V to charge it. The solar panel must be able to deliver this voltage to the battery after power losses and voltage drop in the cables and charge controller and in conditions in which the solar cells operate at a high temperature. A solar panel with a Voc of about 20V is required to reliably charge a 12V battery.
    Charge Controllers
    A charge controller is designed to protect the battery and ensure it has a long working life without impairing the system efficiency. Batteries should not be overcharged and the function of the charge controller is to ensure that the battery is not over charged. Charge controllers are designed to function as follows:
        •       protect the battery from over-discharge, normally referred to as low voltage disconnect (LVD) that disconnects the battery from the load when the battery reaches a certain depth of discharge (DOD).
        •       protect the battery from over-charging by limiting the charging voltage - this is important with sealed batteries - it is usually referred to as high voltage disconnect (HVD).
        •       prevent current flowing back into the solar panel during the night, so called reverse current.
    The power requirements of standalone solar systems are rarely in sync with the battery charging. Appliances and loads need to be powered when there is sufficient solar radiation, during overcast weather and during the night. Bad weather may last for several days and the daily charging and discharging of the batteries takes its toll on them. Batteries that are able to handle the constant charging and discharging are known as deep cycle batteries. Batteries need to have a good charging efficiency, low charging currents and low self-discharge.
    The Ah efficiency of a battery describes the relationship between the Ah that are put into the battery and the Ah that are taken out. Under ideal conditions a new deep-cycle battery would be 90% efficient.
    Choosing the most appropriate battery
    The important characteristics to look for are:
    • capacity
    • cycle life  price / performance
    • size and space requirements
    • Ah efficiency
    • self-discharge rate
    • installation - vertical or horizontal
    • environmental - will batteries be placed near water supplies or in wildlife parks etc                                                                                                                                          
    Cables and accessories
    Cables need to be UV resistant and suitable for outdoor applications. It is very important to keep power losses and voltage drop in the cable to a minimum. It is recommended that this be less than 3% between the the array and the batteries and less than 5% between the battery and DC loads.
    Stand-Alone System Design Procedure
    1. Determine how much electricity you need
    Load calculation can be down in two ways, either calculated on a daily basis or weekly. Regardless of which you choose you need to be as accurate as possible.
    2. Decide which type of battery you will need                                                      
    Battery Storage is usually expressed in Amp hours (Ah). However, it can be given in Watt hours.
    3.) Calculate how much sun your site receives.                                                          
    Take into account the design month - the month when there is the least sun and the most demand.
    4.) Approximation of Array Size - If the system is going to be used all year round and the energy requirement is fairly constant then the design month will be when the weather is at its worst.


    © 2015 Go Solar Green NY. All Rights Reserved.